If you remember any of the people, places or machines pictured in the photographs please share your memories by clicking on the words Add a comment about this page below.
Author
By ALISTAIR ADAMS
Page added
23/09/2013
Comments about this page
Hi David,
I am sure we could all remember some ‘Incidents’.
Two in the works come to my mind, (although I do remember a couple on site too).
I worked mainly in Hydraulic 2 in the 1960’s so both of these relate to that fitting shop.
Firstly, some studs failed in a flange holding an elbow under pressure at the ‘Clocking in’ end of the shop. A horizontal column of oil went nearly to the other end of the shop, before it dropped to the floor. Luckily no-one was in its way. The oil was a red, anti – inflammatory grade and very expensive!
The second incident I did not see, but was told about. A fitter was checking for a leak in a pressurised hydraulic system, with his thumb!
He found it when the vapourised oil inflated his thumb. Not a good move. He did not lose his digit, luckily.
I will not name him, it could be embarrassing. I have seen him at an F&P function in the last couple of years!
By ALISTAIR ADAMS (31/05/2015)
I remember two potentially serious incidents in No1 hydraulic in the early sixties.
A Newman Hender 24 inch gas main gate valve blew its top off just as Dick Brain was inspecting the seat for leaks. The valve blew Dick backwards and the valve fell the other way taking another five? valves with it. Dick was surprised but not hurt and the only damage was to the valves.
The cause was found to be a design change from Newman Hender from 24 (I think) 2 inch studs to a circlip design with no radii in the location groove corners.
All valves when stripped were shown to be on the point of failure.
Another instance was a vey high pressure cylinder (120,000 PSI) for Berkley Laboratories as I remember.
It was set up in the deep end of the large pit in the bottom bay. As the pressure took all morning building up we all had regular trips to look over the railing and monitor the pressure, I think on my last look the gauge showed circa 80,000 PSI.
Then a loud bang, everyone hurried to see what had happened. A blanking plug had blown out of the end of the cylinder and made a hole about six foot diameter and going eighteen inches into the wall.
By David Budrey (24/05/2015)
What a brilliant page! Thanks for adding it Alistair! Hope someone can remember what happened that day and who’s pictured in the photos?!
We use cookies to optimize our website and our service.
Functional Always active
The technical storage or access is strictly necessary for the legitimate purpose of enabling the use of a specific service explicitly requested by the subscriber or user, or for the sole purpose of carrying out the transmission of a communication over an electronic communications network.
Preferences
The technical storage or access is necessary for the legitimate purpose of storing preferences that are not requested by the subscriber or user.
Statistics
The technical storage or access that is used exclusively for statistical purposes.The technical storage or access that is used exclusively for anonymous statistical purposes. Without a subpoena, voluntary compliance on the part of your Internet Service Provider, or additional records from a third party, information stored or retrieved for this purpose alone cannot usually be used to identify you.
Marketing
The technical storage or access is required to create user profiles to send advertising, or to track the user on a website or across several websites for similar marketing purposes.
Comments about this page
Hi David,
I am sure we could all remember some ‘Incidents’.
Two in the works come to my mind, (although I do remember a couple on site too).
I worked mainly in Hydraulic 2 in the 1960’s so both of these relate to that fitting shop.
Firstly, some studs failed in a flange holding an elbow under pressure at the ‘Clocking in’ end of the shop. A horizontal column of oil went nearly to the other end of the shop, before it dropped to the floor. Luckily no-one was in its way. The oil was a red, anti – inflammatory grade and very expensive!
The second incident I did not see, but was told about. A fitter was checking for a leak in a pressurised hydraulic system, with his thumb!
He found it when the vapourised oil inflated his thumb. Not a good move. He did not lose his digit, luckily.
I will not name him, it could be embarrassing. I have seen him at an F&P function in the last couple of years!
I remember two potentially serious incidents in No1 hydraulic in the early sixties.
A Newman Hender 24 inch gas main gate valve blew its top off just as Dick Brain was inspecting the seat for leaks. The valve blew Dick backwards and the valve fell the other way taking another five? valves with it. Dick was surprised but not hurt and the only damage was to the valves.
The cause was found to be a design change from Newman Hender from 24 (I think) 2 inch studs to a circlip design with no radii in the location groove corners.
All valves when stripped were shown to be on the point of failure.
Another instance was a vey high pressure cylinder (120,000 PSI) for Berkley Laboratories as I remember.
It was set up in the deep end of the large pit in the bottom bay. As the pressure took all morning building up we all had regular trips to look over the railing and monitor the pressure, I think on my last look the gauge showed circa 80,000 PSI.
Then a loud bang, everyone hurried to see what had happened. A blanking plug had blown out of the end of the cylinder and made a hole about six foot diameter and going eighteen inches into the wall.
What a brilliant page! Thanks for adding it Alistair! Hope someone can remember what happened that day and who’s pictured in the photos?!
Add a comment about this page